Settings Telephne Update and Provisioning

•

> Paramètres > Système > Mise à jour et provisioning)

If no update server is available, you can initiate an update by loading a firmware file in the telephone from your hard disk or from a data storage device.

Note: The automatic installation of updates is switched off when you perform a manual update. You can switch the automatic installation of updates on again under

> Paramètres > Système > Mise à jour et provisioning > Mise à jour automatique.

Requirements:

•

Firmware file (*.rom) saved on the data storage device

•

Data storage device inserted into slot

Notes:

You find the firmware file on the Internet (Auerswald: www.auerswald.de/service, FONtevo: support.fontevo.com).

To get information about the firmware version that is currently saved in the telephone, select

> Paramètres > Système > Informations à propos du téléphone or, in the Configuration Manager, click on the logo at the top right with the left-hand mouse button.

Select the firmware file (*.rom) > Update. To activate the new firmware, click Redémarrage.

Notes:

To restart the telephone at a later point in time, tap on Annuler and then, under Settings > System > Update & provisioning > Reboot, tap on Redémarrage when you want to restart the telephone.

After a firmware update you usually require a new version of the instructions. You find up-to-date instructions on the Internet (Auerswald: www.auerswald.de/service, FONtevo: support.fontevo.com).

In order to use the new features after the telephone's firmware has been updated, you often may need to update the PBX firmware (see PBX operation instructions).

Schedule

The schedule specifies the weekday and time at which the update and provisioning are to be performed.

Note: To avoid overloading of the provisioning server, the automatic update and provisioning starts within a time slot of 60 minutes after the set time.

Heure

Indicates when provisioning is to be performed.

Jours de la semaine programmés

Indicates the week days on which the update and provisioning is to be performed.

Provisioning settings

Provisioning automatique

During automatic provisioning the configuration data is automatically loaded in the telephone from the provisioning server, at the set point in time. The system checks if a new firmware update is available on the update server. If an update is available, the new firmware is also loaded into the telephone if the automatic installation of updates is selected.

Requirements:

•

The PBX or telephone must be connected to a broadband Internet connection

•

Address of the DNS server entered on the Paramètres > Réseau > Réseau

•

The set schedule must be entered on the Paramètres > Système > Mise à jour et provisioning > Mise à jour

•

The URL of the provisioning server must be entered on the Paramètres > Système > Mise à jour et provisioning > Provisioning

•

When automatic provisioning is performed: Data storage device inserted into slot

Provisioning avec données DHCP

The telephone receives the IP address of the provisioning server from a DHCP server. In addition to IP addresses, it is also possible to transmit further data to control the provisioning process.

Serveur de redirection

The telephone receives the IP address of the provisioning server from the redirect server.

Provisioning avec recherche de systèmes

The automatic configuration of the telephones is carried out via the PBX.

URL serveur de provisioning

If automatic provisioning of the configuration data is not carried out via DHCP data or via a redirection server, you must enter the URL of the provisioning server.

Note: You find further information about the provisioning process on the Internet (see www.auerswald.de/service under Developer).

Test de provisioning

You can check the provisioning settings, and the way the server works, by initiating a one-time provisioning test.

Requirements:

•

The PBX or telephone must be connected to a broadband Internet connection

•

The address of the DNS server must be entered in

> Paramètres > Réseau > Réseau

•

Under

> Paramètres > Système > Mise à jour et provisioning > Mise à jour automatique, enable the Vérifier la disponibilité de mises à jour check box

•

Under

> Paramètres > Système > Mise à jour et provisioning > Paramètres du provisioning, enable the Provisioning automatique check box

•

The address of the provisioning server must be entered under

> Paramètres > Système > Mise à jour et provisioning

•

Data storage device inserted into slot

Important: As soon as you tap on Test de provisioning, this may delete the existing configuration and firmware data, which will be replaced by new data. The telephone is restarted.

If the update and provisioning settings for the telephone are correct, and configuration and firmware data is present on the servers, this data is loaded in the telephone. The firmware is enabled by an immediate restart of the telephone.

If the update and provisioning settings for the telephone are incorrect, or no data is present on the servers, a message that provisioning has failed is displayed in the status line on the telephone.

Notes:

After a firmware update you usually require a new version of the instructions. You find up-to-date instructions on the Internet (Auerswald: www.auerswald.de/service, FONtevo: support.fontevo.com).

In order to use the new features after the telephone's firmware has been updated, you often may need to update the PBX firmware (see PBX operation instructions).

Autorisation de la configuration à distance via messages SIP

Note: You find further information about configuration via SIP messages on the Internet (see www.auerswald.de/service under Developer).

The telephone is configured via incoming SIP messages. An additional entry must be made:

IP address of configuration server (1-5)

Configure at least one configuration server.

Update settings

When performing an automatic update the system checks whether a new firmware update is available on the update server, at the set point in time. If an update is available, the new firmware is loaded into the telephone if the automatic installation of updates is selected.

Requirements:

•

The PBX or telephone must be connected to a broadband Internet connection

•

Address of the DNS server entered on the Paramètres > Réseau > Réseau

•

The set schedule must be entered on the Paramètres > Système > Mise à jour et provisioning > Mise à jour

•

The address of the update server must be entered on the Paramètres > Système > Mise à jour et provisioning > Mise à jour

•

When the automatic update is performed: Data storage device inserted into slot

Vérifier la disponibilité de mises à jour

Installer les mises à jour disponibles

Notes:

If only the Vérifier la disponibilité de mises à jour check box is selected, the system only checks for the availability of a new firmware version and, if there is one, it displays it. The firmware is not updated until the Installer les mises à jour disponibles check box is selected.

After a firmware update you usually require a new version of the instructions. You find up-to-date instructions on the Internet (Auerswald: www.auerswald.de/service, FONtevo: support.fontevo.com).

In order to use the new features after the telephone's firmware has been updated, you often may need to update the PBX firmware (see PBX‘s Advanced Information).

URL du serveur de mise à jour

To automatically update the firmware you must enter the URL of the update server. The URL of the update server is already entered in the factory settings. However, if it is not, or if you want to change the URL, follow the instructions below.

Mise à jour du firmware > Mise à jour

If you have entered the address of an update server, you can check the update settings and the functioning of the server by performing an update test.

Requirements:

•

The PBX or telephone must be connected to a broadband Internet connection

•

The address of the DNS server must be entered in Paramètres > Réseau > Réseau

•

The address of the update server must be entered in Paramètres > Système > Mise à jour et provisioning > Mise à jour

•

data storage device inserted into slot

The check for new firmware is carried out.

If no firmware file is available on the update server, a warning message is displayed to tell you that no new firmware is available.

If the telephone's update settings are incorrect, a warning message is displayed to tell you that the check for new firmware was unsuccessful.

If the update settings of the telephone are correct and a firmware file is available on the update server, the new firmware is installed. The telephone is restarted, and the login window opens.

Notes:

To restart the telephone at a later point in time, tap on Annuler and then, under Paramètres > Système > Mise à jour et provisioning > Redémarrage, tap on Redémarrage when you want to restart the telephone.

After a firmware update you usually require a new version of the instructions. You will find up-to-date instructions on the Internet (Auerswald: www.auerswald.de/service, FONtevo: support.fontevo.com).

In order to use the new features after the telephone's firmware has been updated, you often may need to update the PBX firmware (see PBX‘s Advanced Information).

Déployer le firmware

A new version of the firmware can be distributed from one system telephone to other system telephones connected to the PBX.

Requirements:

•

Enabled Déployer le firmware check box

Note: If the check box Déployer le firmware is enabled, the distribute.rom file will, during an update, be automatically created on the corresponding data storage device.

•

Current firmware version on the distributing telephone

•

Data storage device inserted into slot of the firmware distributing telephone with firmware file. The firmware file must be renamed into distribute.rom

Note: The distribute.rom file can be saved onto the data storage device either via the file manager (see chapter Settings > File Manager) or PC. You find current firmware versions on the Internet (Auerswald: www.auerswald.de/service, FONtevo: support.fontevo.com).

•

Firmware version in the telephone must correspond to the distribute.rom file on the data storage device

Notes:

The telephone that receives the firmware must have a firmware version as of 2.4.

The PBX must have a firmware version as of 6.6.

Distributing the firmware is possible from one COMfortel 3600 IP to other COMfortel 3600 IP and from COMfortel 1400 IP/2600 IP to other COMfortel 1400 IP/2600 IP.

When operating the telephone on another PBX than the PBX, the telephone can be updatet directly from the firmware distributing telephone. For this, you must enter the update URL http://<IP address>/distribute in the telephone.

Firmware may be distributed. The telephone that distributes the firmware is at this moment used as update server.