Settings Configuration Manager Update and Provisioning

•

Using the Configuration Manager (page Ρυθμίσεις > Σύστημα > Ενημέρωση & παροχή)

> Search

If no update server is available, you can initiate an update by loading a firmware file in the telephone from your hard disk or from a data storage device.

Note: The automatic installation of updates is switched off when you perform a manual update. You can switch the automatic installation of updates on again under

> Ρυθμίσεις > Σύστημα > Ενημέρωση & παροχή > Αυτόματη ενημέρωση.

Requirements:

•

Firmware file (*.rom) saved on the hard disk

Notes:

You find the firmware file on the Internet (Auerswald: www.auerswald.de/service, FONtevo: support.fontevo.com).

To get information about the firmware version that is currently saved in the telephone, select

> Ρυθμίσεις > Σύστημα > Πληροφορίες τηλεφώνου or, in the Configuration Manager, click on the logo at the top right with the left-hand mouse button.

Select the firmware file (*.rom) > Save. To activate the new firmware, click Επανεκκίνηση.

Notes:

To restart the telephone at a later point in time, tap on Ακύρωση and then, under Ρυθμίσεις > Σύστημα > Ενημέρωση & παροχή > Επανεκκίνηση, tap on Επανεκκίνηση when you want to restart the telephone.

After a firmware update you usually require a new version of the instructions. You find up-to-date instructions on the Internet (Auerswald: www.auerswald.de/service, FONtevo: support.fontevo.com).

In order to use the new features after the telephone's firmware has been updated, you often may need to update the PBX firmware (see PBX operation instructions).

Schedule

The schedule specifies the weekday and time at which the update and provisioning are to be performed.

Note: To avoid overloading of the provisioning server, the automatic update and provisioning starts within a time slot of 60 minutes after the set time.

Ώρα

Indicates when provisioning is to be performed.

Προγραμματισμένες ημέρες εβδομάδας

Indicates the week days on which the update and provisioning is to be performed.

Update settings

When performing an automatic update the system checks whether a new firmware update is available on the update server, at the set point in time. If an update is available, the new firmware is loaded into the telephone if the automatic installation of updates is selected.

Requirements:

•

The PBX or telephone must be connected to a broadband Internet connection

•

Address of the DNS server entered on the Ρυθμίσεις > Δίκτυο > Δίκτυο

•

The set schedule must be entered on the Ρυθμίσεις > Σύστημα > Ενημέρωση & παροχή > Ενημέρωση

•

The address of the update server must be entered on the Ρυθμίσεις > Σύστημα > Ενημέρωση & παροχή > Ενημέρωση

•

When the automatic update is performed: Data storage device inserted into slot

Έλεγχος για ενημερώσεις

Εγκατάσταση διαθέσιμων ενημερώσεων

Notes:

If only the Έλεγχος για ενημερώσεις check box is selected, the system only checks for the availability of a new firmware version and, if there is one, it displays it. The firmware is not updated until the Εγκατάσταση διαθέσιμων ενημερώσεων check box is selected.

After a firmware update you usually require a new version of the instructions. You find up-to-date instructions on the Internet (Auerswald: www.auerswald.de/service, FONtevo: support.fontevo.com).

In order to use the new features after the telephone's firmware has been updated, you often may need to update the PBX firmware (see PBX‘s Advanced Information).

Διανομή υλικολογισμικού

A new version of the firmware can be distributed from one system telephone to other system telephones connected to the PBX.

Requirements:

•

Enabled Διανομή υλικολογισμικού check box

Note: If the check box Διανομή υλικολογισμικού is enabled, the distribute.rom file will, during an update, be automatically created on the corresponding data storage device.

•

Current firmware version on the distributing telephone

•

Data storage device inserted into slot of the firmware distributing telephone with firmware file. The firmware file must be renamed into distribute.rom

Note: The distribute.rom file can be saved onto the data storage device either via the file manager (see chapter Settings > File Manager) or PC. You find current firmware versions on the Internet (Auerswald: www.auerswald.de/service, FONtevo: support.fontevo.com).

•

Firmware version in the telephone must correspond to the distribute.rom file on the data storage device

Notes:

The telephone that receives the firmware must have a firmware version as of 2.4.

The PBX must have a firmware version as of 6.6.

Distributing the firmware is possible from one COMfortel 3600 IP to other COMfortel 3600 IP and from COMfortel 1400 IP/2600 IP to other COMfortel 1400 IP/2600 IP.

When operating the telephone on another PBX than the PBX, the telephone can be updatet directly from the firmware distributing telephone. For this, you must enter the update URL http://<IP address>/distribute in the telephone.

Firmware may be distributed. The telephone that distributes the firmware is at this moment used as update server.

URL διακομιστή ενημέρωσης

To automatically update the firmware you must enter the URL of the update server. The URL of the update server is already entered in the factory settings. However, if it is not, or if you want to change the URL, follow the instructions below.