SIP
Proceed as follows:
•Separately for VoIP providers
•Using the Configuration Manager: Réseaux publics > VoIP > Fournisseur > Configurer
Note: You can obtain the data for the settings either directly from the VoIP provider or from suitable lists in the Internet.Requirements:
•For entering a URL: configured DNS server
•For using a STUN server: IP operating mode IPv4
FOURNISSEUR
Select the provider to be displayed/configured.
Domaine
The domain (also known as a "realm", "SIP domain" or "SIP realm") is required for the VoIP address. The structure of a subscriber's VoIP address is similar to an e-mail address. It is made up of the VoIP phone number and the domain, separated by the @ character: <subscriber>@domain.
Résolution de nom
There are both country-specific and provider-specific reasons why name resolution is not always successful via the default gateway. In such cases, another way should be chosen here.
Résolution de nom via la configuration IP
There are several accounts at this domain and the name resolution for another account at this domain has alreday been configured.
Note: It is possible to set the name resolution differently for the accounts of the same domain.Via l’accès Internet utilisé
The name resolution takes place via the selected IAD under Accès Internet utilisé. The DNS server provided by the provider is used.
Utiliser son propre DNS (via le dispositif d’accès intégré)
The DNS servers that are entered below are used via the selected IAD under Accès Internet utilisé.
Premier serveur DNS/Deuxième serveur DNS
IPv4: 4 blocks with 3 digits separated by a dot (.).
IPv6: 8 blocks with 4 digits or letters separated by a colon (:).
Note: If an IPv6 address is entered as DNS server, then the IAD selected under Accès Internet utilisé must also have an IPv6 address.Registre|Port
REGISTER requests are sent to the specified registrar (also known as a SIP registrar, registry, SIP server, SIP registry server). Enter this data as an IP address or a URL.
Note: Synthèses > Ports: The page shows an overview of the PBX ports (incoming and outgoing).Note: You should only switch off the registrar if the VoIP provider requires you to do so. No NAT Keep-Alive is performed if the registrar is disabled. An internal network is usually protected from external manipulation by, for example, a firewall integrated in the router. Without NAT Keep-Alive, the firewall's security functions will defend you against attempted accesses from the Internet. For this reason, you may need to implement port forwarding for incoming SIP packets on the SIP port set up in the VoIP provider's configuration.
Caution:Each time a port is opened on the router, this creates a potential security risk.•It is essential you put additional protective measures in place.
Délai pour l’enregistrement (1 à 60 min.)
The registration time specifies how many minutes the PBX waits before reregistering itself with the VoIP provider.
Note: In the test phase, after configuring the VoIP provider, we recommend you enter a low value (e.g. 3 minutes). After completing the test phase, you can enter a much higher value, since some VoIP providers also reject calls if too many attempts are made to register.Enregistrement SIP conformément à RFC 6140
The SIP protocol SIPconnect 1.1 is used by the PBX.
Réinscription après SIP Forbidden (403)
If a SIP Forbidden (403) is received on an INVITE, the involved provider is re-registered.
Réenregistrement après SIP Timeout (408, 503)
If a SIP Timeout (408, 503) is received on an INVITE, the involved provider is re-registered.
NAT Traversal
NAT (Network Address Translation) enables you to convert a particular IP address that is used within a network (e.g. a local network) into a different IP address that can be used by a different network (e.g. the public switched phone network). If NAT traversal is enabled, and a query is sent from a local IP address to the public network, the sending IP address is swapped with the public IP address. This function is performed in the reverse direction for the reply.
désactivé (utilisez l’adresse locale)
NAT traversal is not performed by the PBX. The router which connects the local area network with the Internet should be a properly functioning SIP-aware router which performs NAT traversal.
activé avec utilisation de STUN
NAT traversal is not performed by the PBX. To achieve this, a STUN server must also be specified for the VoIP provider.
activé (sous l’utilisation de rport)
NAT traversal is not performed by the PBX. To achieve this, the registrar for the VoIP provider must be switched on. The SIP request also contains an "rport" part in which the IP addresses used here (local, public) are transported.
Note: When selecting activé: If you have problems with one-way calls, set the following function instead: activé avec utilisation de STUN.Caution:Each time a port is opened on the NAT router, this creates a potential security risk.•It is essential you put additional protective measures in place.
utilisier l’adresse IP publique statique
Requirements:
•Registered fixed IP address (see Preferences)
If the VoIP provider requires it: NAT traversal is performed by the PBX.
NAT Traversal additional settings
Public IP address in Via and Contact headers can be enabled for both fixed and dynamically assigned IP addresses. However, the setting only makes sense when using UDP.When using TCP and TLS, providers sometimes explicitly require the use of the internal IP address. The external IP address should only be used if the provider requires port forwarding of the SIP ports for successful operation. Otherwise the PBX may not be able to receive all calls.utiliser l’adresse IP publique dans l’en-tête VIA
If the provider requires it: The public IP address is used in the VIA Header.
Utilisez les paramètres ';alias' et ';keep' dans l’en-tête VIA
If the provider requires it: These parameters are used in the VIA Header.
The option prevents the PBX from losing registration and should therefore always be enabled.utiliser l’adresse IP publique dans l’en-tête du contact
If the provider requires it: The public IP address is used in the Contact Header.
When using UDP, at least this setting should be enabled.utiliser le paramètre ';ob' dans l’en-tête du contact
If the provider requires it: This parameter is used in the Contact Header.
The option prevents the PBX from losing registration and should therefore always be enabled.Interval for NAT Keep-Alive actif
After the time specified here has passed, NAT Keep-Alive packets are sent to the firewall to maintain the NAT mapping.
Note: Some VoIP providers block accounts if the Interval for NAT Keep-Alive is too short. As a rule, this is reported with error message 503 during SIP registration. If you experience this problem, it is advisable to increase the value (e.g. to 180).Par défaut
Default setting
Option SIP
Use this setting for non-registered connections between the VoIP provider and the PBX for re-registration.
Proxy sortant/Session Border Controller
The outbound proxy is an intermediate server that processes all VoIP requests and connections going to the provider (except for registration).
désactivé
The outbound proxy is disabled.
automatique
The PBX automatically determines an outbound proxy.
manuel Port
The outbound proxy is a fixed default setting. Enter this data as an IP address or a URL.
Note: Synthèses > Ports: The page shows an overview of the PBX ports (incoming and outgoing).SIP port (1 to 65535)
The SIP port on the PBX is used both as an incoming port and an outgoing port (i.e. for communications with the VoIP provider).
Note: A different SIP port must be used for each VoIP provider.Note: The SIP port for a VoIP provider cannot be the same as the Port SIP du registre VoIP interne or the Port SIPS du registre VoIP interne.Note: The Synthèses > Ports page shows an overview of the PBX ports (incoming and outgoing).SIP session timer (5 to 60 min.)
At the specified intervals, the SIP session timer checks whether the connection is still present. (The PBX cannot detect whether a call connection is disrupted due to problems on the provider side.)
Note: When the SIP session timer is switched on, this may result in the call being interrupted more frequently after the specified interval, if a VoIP provider has not implemented session renewal properly. In this case, you should adjust the interval of the SIP session timer or switch it off.Désactivation de SIP Prack (RFC 3262)
The negotiation of SIP option „100rel“ is disabled. This might be necessary if the provider supports „SIP-Forking“.
Numérotation en bloc uniquement|Temps d’attente après composition du dernier chiffre (1 à 15 sec.)
A connection is not set up to transmit the digits dialled here to the provider until the delay time after the last digit is dialled has passed, all the digits are then sent as a block. Time measurement restarts after each digit entry. After the set time has elapsed, the PBX recognises the previously dialled digit as the last digit and does not allow any further entries.
Note: En-bloc dialling is useful, for example, if there are problems with single digit dialling in sub-system operation.Note: Since the PBX does not forward the entire phone number to the exchange until the set time has elapsed, select the time as short as possible.Note: The default value for manual entries is approx. 3 seconds.SIPS Structure URL
Requirements:
•External VoIP channel that supports SIPS (optional, see Technical Data in the Instructions)
•A certificate for the VoIP provider stored in the PBX
This provider encrypts external connections to prevent listening in. The processes used to set up and shut down a connection, and signalling, are all encrypted by SIPS.
SIPS
Encryption of SIPS via TLS.
SIP/TLS
Encryption of SIP via TLS.
Note: SRTP is used to encrypt call data.Désactiver la vérification du nom d’hôte
No verification whether the certificate belongs to the domain/IP.
Gérer les certificats
Opens the certificates management.
Transport SIP
Selection of the transport protocol.
Protocole IP
IPv4
IPv4 operating mode is used for communications with the VoIP provider.
IPv6
IPv6 operating mode is used for communications with the VoIP provider.
automatique
The PBX first checks whether the VoIP provider supports IPv6. If so, operating mode IPv6 is used for communications with the VoIP provider. Otherwise, operating mode IPv4 is used.
Note: If the actual IP operating mode is IPv6, STUN cannot be used as a NAT method either for SIP or RTP.Sécurité accrue
The provider provides better levels of security to protect the PBX against external attacks.