Buch1 > Using the Configuration Manager > Devices > Door Terminals > Management of the Door Terminal > Door Calls+Relays
Door Calls+Relays
Proceed as follows:
•Using the Configuration Manager (Devices > Door terminals)
Phone Number
Internal number, freely selectable from the numbers in the internal phone number supply. This number can be called directly by an internal subscriber. When put together with the numbers of the door bell buttons, this creates 3 to 4-digit phone numbers. (Select Devices > Device wizard > New)
*Note: Double allocation of a number is not possible.
*Note: Using numbers with few digits (two or three-digit numbers) inevitably restricts the possible supply of numbers requiring more digits. For example, if the number 12 is assigned, the numbers 120-129 and 1200-1299 will no longer be available.
*Note: The default exchange line access number on the PBX is 0 in the factory settings. However, this can be changed. Note that changing the exchange line access number restricts the dial plan.
Name
Freely selectable name. This name is used to identify the door terminal within the PBX and the connected system phones. The name can also be transferred to the VoIP end devices via LDAP server.
Module | Port
Module and port to which the device that can be used as door terminal (e. g. a TFS Universal-Plus) is connected.
Configure
Opens the configuration of the door terminal.
Relais
Requirements:
•Relay/actuator (optional, see Technical Data in the Instructions)
•Created door terminal
A relay is assigned to the door station with the operating mode Speaking, Door opener or Light.
A relay used for this purpose can, for example, be part of a connected door terminal or be connected to the same port (a/b Switching Module). Alternatively, it is also possible to use a relay for the door function which is part of another connected device (e.g. an IP switch relay). In this case it must first be created in the configuration of the PBX as part of this other device and then be assigned to the door terminal. It then remains part of this other device in the configuration of the PBX, but takes over the selected door function for the door terminal.
Devices > Relays (actuators): If matching relays are already set up on the page, a list field appears. Select one of the existing relays in the list field and confirm with .


If you do not want to use any of the existing relays, select New relay in the list field ( cancels the operation). Assign a freely selectable relay name an confirm with Ok.
*Note: Devices > Relays (actuators): Alternatively, relays can be created and assigned here.
*Further help under Relay operating modes.
Link to page Devices > Relays (actuators)
Deletes the relay or opens the configuration of the relay.
Türrufe
Requirements:
•Switch input (optional, see Technical Data in the Instructions)
•Created door terminal
The door bell buttons of a door terminal can be used to initiate configuration-dependent internal and external door calls. For this purpose, the door bell buttons must be created as switch inputs in the PBX. They must then be allocated call destinations and assigned to the door terminal. To detect a door call, e.g. because a door bell button has been pressed, the PBX needs to know which DTMF sequence or which SIP invite the connected device sends in this case (see manual and settings of the device in question).
*Note: The DTMF sequence or the SIP invite usually is the phone number assigned to the door bell button within the door terminal. After the door terminal has been configured in the configuration of the PBX, the door call distribution will be controlled completely – including configuration-dependently – by the PBX.
Door Calls + Relays: Click on the lower in the line of the corresponding door terminal.
Switch input: Enter the designation for the switch input.
DTMF sequence(analogue door terminals)/SIP invite(VoIP door terminals): Enter values. To detect that the alarm has been triggered, e. g. because a door bell button has been pressed, the PBX needs to know which DTMF sequence or which SIP invite the connected device sends in this case (see manual and settings of the device in question). The DTMF sequence or the SIP invite usually is the phone number assigned to the door bell button within the door terminal.
list fieldDestination number: Select the desired call destination.
alternative:
Select Enter destination number and enter the desired call destination under Destination number
Possible entries:
External number
Short-code number
Internal telephone number of the individual telephone
Internal telephone number of the group
*Note:
*Note: The call destination is first entered identically for all configurations. It can be changed afterwards.
*Note: If a door call should also be executed via VoIP accounts or GSM gateways, the external number must always be entered with the corresponding local area code even if it is the local prefix.
Click Ok.
*Note: To make further settings for a door call or the associated switch input, click in the line of the corresponding door call on .
*Further help under Switch Input
Deletes the switch input or opens the configuration of the door call.