Basic Network Settings
Proceed as follows:
Separately for groups
Using the Configuration Manager (Groups > Features)
GROUP
Select the group you want to display/configure.
*Important: The settings done are only valid on the condition that they are not overridden by a profile. The simultaneous display takes place on page Groups > Features under Overridden by profile in configuration.
*Note: [Name configuration] ...: In the displayed configuration, the function is overridden by the displayed setting. Configuration via the Configuration Manager (Groups > Profiles> ...)
*Note: not overridden by a profile: The function is currently not overridden by a profile.
*Note: (not profile-controlled): The function cannot be controlled with a profile.
Ringing sequence | after:
All
All subscribers logged-in to the group will ring simultaneously. Selected subscribers will start to ring after the configured delay time (after:). If a call was not accepted, although all logged-in members of the group were called, the call would be finished with a busy signal.
All - Split Group
The call is handled almost similar to the ringing sequence All. The only difference is the way multiple calls to the group are handled: If the group receives further calls during an active call, the group will be split into several smaller groups ringing for a specific active call. But there will never ring more calls in the group than the number of free available group members. Additional calls will be rejected with a busy then. If a call is accepted the other phones ringing so far for this call are assigned to the other pending calls and will immediately start to ring again. If a group member finishes a call, this subscriber will immediately ring again for the pending calls. The timer for the configured delay time (after:) starts after receiving the first call to the group and will not restart for additional incoming calls.
Linear - fixed - Split Group
Only the phone of one group member will ring. After the configured delay time (after:) another single group member will be called. The order of calls depends on the configured Priority. If a call was not accepted, although all logged-in members of the group were called, the call would be finished with a busy signal.
Linear - balancing - Split Group
Only the phone of one group member will ring. After the configured delay time (after:) another single group member will be called. The order of the calls depends on the configured Priority: First of all the member of the group first logged-in gets the position 1 in the order of calls, the second one the position 2, ... . If position 1 takes a call, the second call will be assigned to position 2. The member of the group with the position 1 will get the last position in the order for a future call after he has finished the current call. If a call was not accepted, although all logged-in members of the group were called, the call would be finished with a busy signal.
Linear - fixed - rotating - Split Group
Only the phone of one group member will ring. After the configured delay time (after:) another single group member will be called. If all members of a group are called, the process will be restarted with the first member of the group of the call order. In the first rotation the next member of the group of the call order will be called immediately if a subscriber is busy. In the second rotation the busy subscribers will hear knocking (only from external). The order of calls depends on the configured Priority.
*Note: System phones control the call waiting itself, so the ringing sequence can vary.
Linear - balancing - rotating - Split Group
Only the phone of one group member will ring. After the configured delay time (after:) another single group member will be called. If all members of a group are called, the process will be restarted with the first member of the group of the call order. In the first rotation the next member of the group of the call order will be called immediately if a subscriber is busy. In the second rotation the busy subscribers will hear knocking (only from external). The order of the calls depends on the configured Priority: First of all the member of the group first logged-in gets the position 1 in the order of calls, the second one the position 2, ... . If position 1 takes a call, the second call will be assigned to position 2. The member of the group with the position 1 will get the last position in the order for a future call after he has finished the current call.
Adding - fixed - Split Group
Here initially only one group members' phone is ringing. After the configured delay time (after:) another single group member will be called. If the group receives another call B initially the free group members will ring one after the other (adding). If for the first call A less than half of the group members are ringing more members are added to this call until exactly the half is reached. If for the first call A more than half of the group members are ringing, no members are added to this call (frozen). Only the remaining subscribers are added to call B. If all group members are already ringing for call A, the group is split for the calls. The order of calls depends on the configured Priority. If a call was not accepted, although all logged-in members of the group were called, the call would be finished with a busy signal.
Adding - balancing - Split Group
Here initially only one group members' phone is ringing. After the configured delay time (after:) another single group member will be called. If the group receives another call B initially the free group members will ring one after the other (adding). If for the first call A less than half of the group members are ringing more members are added to this call until exactly the half is reached. If for the first call A more than half of the group members are ringing, no members are added to this call (frozen). Only the remaining subscribers are added to call B. If all group members are already ringing for call A, the group is split for the calls. The order of the calls depends on the configured Priority: First of all the member of the group first logged-in gets the position 1 in the order of calls, the second one the position 2, ... . If position 1 takes a call, the second call will be assigned to position 2. The member of the group with the position 1 will get the last position in the order for a future call after he has finished the current call. If a call was not accepted, although all logged-in members of the group were called, the call would be finished with a busy signal.
Adding - fixed - rotating - Split Group
Here initially only one group members' phone is ringing. After the configured delay time (after:) another single group member will be called. If the group receives another call B initially the free group members will ring one after the other (adding). If for the first call A less than half of the group members are ringing more members are added to this call until exactly the half is reached. If for the first call A more than half of the group members are ringing, no members are added to this call (frozen). Only the remaining subscribers are added to call B. If all group members are already ringing for call A, the group is split for the calls. The order of calls depends on the configured Priority. If finally all logged-in members of a group are called, the busy subscribers will hear knocking additionally (only from external).
Adding - balancing - rotating - Split Group
Here initially only one group members' phone is ringing. After the configured delay time (after:) another single group member will be called. If the group receives another call B initially the free group members will ring one after the other (adding). If for the first call A less than half of the group members are ringing more members are added to this call until exactly the half is reached. If for the first call A more than half of the group members are ringing, no members are added to this call (frozen). Only the remaining subscribers are added to call B. If all group members are already ringing for call A, the group is split for the calls. The order of the calls depends on the configured Priority: First of all the member of the group first logged-in gets the position 1 in the order of calls, the second one the position 2, ... . If position 1 takes a call, the second call will be assigned to position 2. The member of the group with the position 1 will get the last position in the order for a future call after he has finished the current call. If finally all logged-in members of a group are called, the busy subscribers will hear knocking additionally (only from external).
Phone number | Name
Group member. (Entry with New)
Priority
Requirements:
Configured ringing sequence: Not All or All - Split Group
Specifies the order of calls within the group for the ringing sequence (change with | ).
Status of incoming calls
Logged in
Logs the phone into the group.
Logged out
Logs the phone out of the group.
Permanently logged in
Permanently logs the phone of a subgroup into the main group.
Status of outgoing calls
Logged in
Logs the phone into the group.
Logged out
Logs the phone out of the group.
Permanently logged in
Permanently logs the phone of a subgroup into the main group.
Ringing delay
Requirements:
Configured ringing sequence: All or All - Split Group
The subscriber rings after the configured delay time (after:).
New
Selects a new group member from the configured subscribers and groups and adds it to the list.
*Note: Up to 40 internal subscribers or groups can be assigned to a group as members.
Delete
Deletes the entries marked in the list.